Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Los Angeles Owner’s Guide
If you’re holding a Barrette cabinet door, drawer front, or hardware piece that’s failed, we can match it, order it, and install it. Most Barrette-specific kitchen remodeling parts in Los Angeles run $180 to $640 installed, depending on whether it’s a hinge, drawer glide, door, or a full cabinet face. You’ll typically notice the problem the moment a door sags, a drawer grinds, or a soft-close mechanism stops catching, and ignoring it usually leads to more expensive damage down the line.
Barrette sourced cabinet components from a rotating list of suppliers over the years, so the exact replacement part depends on the vintage of your kitchen. That’s why matching specs matters more than matching a nameplate.
Which Barrette Models This Applies To
Barrette kitchens in Los Angeles span roughly two decades of production, and the hardware changed quietly over those years. Early-2000s lines used European 35mm cup hinges with a three-hole mounting plate. Later runs shifted to a two-hole plate with a wider bore spread. The difference is small on paper, about 4mm, but it’s the difference between a door that hangs flush and one that sits crooked no matter how much you adjust it.
Before you order anything, check the backside of the door or drawer box. Barrette stamped most cabinet boxes with a production code, usually four to six digits, on the inside of the sink base cabinet or the top corner of an upper box. If that sticker is gone, measure the hinge cup diameter. 35mm is the standard, but some Barrette doors used a 26mm cup, and those require a specific hinge that isn’t interchangeable. We stock both sizes on the truck and can match what’s there in one trip.
On the OEM versus aftermarket question: for hinges and drawer glides, Blum, Salice, and Grass are solid aftermarket equivalents that fit Barrette openings correctly. For finished doors and drawer fronts, you’ll want a matched replacement from the same material lot, because stained wood and painted finishes vary from batch to batch. We order those directly and color-match on site. Sawyer Remodeling is an independent service provider and not affiliated with Barrette, but we work with their components regularly enough to know the quirks.
Styles & brands we work with
Signs Your Barrette Kitchen Remodeling Is Failing
- Door sag that won’t adjust out: The hinge knuckle is worn or the mounting plate screw holes have stripped. Tightening the screws buys a week, but the door will sag again because the hinge body itself is done.
- Drawer that catches or grinds mid-slide: The ball bearings inside the glide have flattened or the nylon wheel cracked. You’ll hear it before you see it, and forcing the drawer just scores the side rails.
- Soft-close no longer catches: The small plastic dampener inside the hinge or glide has snapped. This is the most common Barrette failure we see in Los Angeles, and it’s a ten-minute fix if you have the right replacement piece.
- Door won’t stay latched or pops open: The catch or touch-latch mechanism is worn past its spring tension. On older Barrette lines, this was a small magnet set that degrades over years of heat and humidity cycling.
- Finish blistering at the bottom corners: Moisture is getting under the finish, usually from sink splashing or repeated steam exposure. The substrate is swelling, and that door or drawer front needs replacement before the problem spreads to the cabinet box.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Barrette-specific kitchen remodel part in Los Angeles, here’s the honest pricing breakdown. Hinge or drawer glide replacement runs $180 to $360 per piece, installed. A single door or drawer front replacement typically lands between $240 and $640, depending on size and finish matching. If the failure exposed a deeper problem, like water damage behind a sink base, the repair becomes part of a kitchen remodel range of $16,520 to $53,100.
What drives the spread is material matching and access. A painted shaker door from a recent Barrette run is faster to match than a stained wood door from twenty years ago, where the finish has aged and mellowed. Labor is transparent: we quote the part, the install time, and the trip separately, then hand you a written price before any work starts. The install itself carries the 365-Day Done Right Promise. If it’s not done right, we make it right.
DIY or Call Us?
A hinge or glide swap is within reach for most homeowners, provided you have the exact replacement part and the right screw depth. The danger is not physical, it’s precision. Barrette’s older cabinets used shorter screws than today’s hardware, and driving a longer one through the door face is a mistake you can’t undo. Same with forcing a slightly-wrong hinge cup, which will blow out the bore and leave you needing a new door.
If the problem is a door, drawer front, or anything involving finish matching, call us at (254) 272-5876. Luca Romano has been working on Los Angeles kitchens for over two decades, and the difference between a matched door and a “close enough” door is something you’ll see every single day.
FAQs
How long do Barrette kitchen components last? In Los Angeles homes, most Barrette hinges and drawer glides last 12 to 20 years with normal use. Soft-close dampeners are the exception, often failing at the 8-to-10-year mark because the plastic degrades with heat and repeated impact.
Can a failed hinge or drawer glide be repaired instead of replaced? No. Once the bearing surface or dampener is worn, there’s nothing to rebuild. The good news is replacement is fast and affordable, usually $180 to $360 installed. Call (254) 272-5876 and we’ll bring the right part to you.
How long does a Barrette parts replacement take? A hinge or glide swap takes about 30 to 60 minutes per piece. A door or drawer front replacement takes a few days, because we order the matched piece and schedule installation once it’s in hand. The Relay Visibility Guarantee means you’ll know exactly when we’re arriving and what the work will cost before we start.
Do you stock Barrette-compatible parts on the truck? Yes. We carry 35mm and 26mm cup hinges, common drawer glide lengths, and soft-close dampeners for both in our Los Angeles service vehicles. If your specific finish needs a custom match, we order it and you’ll have a written price first.
Good work doesn’t need a sales pitch – it just needs to be done right. Call (254) 272-5876 for a free estimate on your Barrette kitchen repair in Los Angeles, and we’ll put the price in writing before you commit.
Written by Luca Romano, Owner, Sawyer Remodeling at Sawyer Remodeling, serving Los Angeles and nearby areas.
