Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Fence Installation: The Los Angeles Owner’s Guide
Installing a Belgard fence in Los Angeles typically costs between $4,130 and $10,620 for a standard residential perimeter, including materials, labor, and concrete footings. We stock Belgard-compatible posts, panels, and hardware on our trucks and can usually start most installations within the week. Most owners call us after a fence section has started leaning, a gate drags against the pavers, or a post has rotted at the base from sprinkler overspray, which is one of the most common failures we see in neighborhoods from Silver Lake to Woodland Hills.
Belgard makes a modular fence system that looks like stacked stone but installs as a precast wall. The product line has evolved over the years, and the failure you’re seeing right now usually comes down to one of three things: a post that wasn’t set deep enough for Los Angeles soil, a gate that’s too heavy for the hinge hardware, or freeze-thaw damage to older panels, even in mild LA winters where nighttime temperatures drop in the canyons.
Which Belgard Models This Applies To
Belgard’s fence line falls under their Westwood and Stonegate collections, with panel sizes running 72 inches wide and heights of 24 to 48 inches. The Westwood line has a rougher, split-face texture; Stonegate panels are smoother and read more contemporary against a modern LA home. Both series use the same post system, which is good news when you’re replacing one broken panel and don’t want to rip out the whole run.
The compatibility gotcha with Belgard fences is the post spacing. Panels slide into aluminum posts, and if you try to use a Westwood panel on a Stonegate post, the channel depth is off by about a half inch. You won’t notice it until the fence starts rattling in the wind, and by then you’ve got a wobble that loosens the post cap. We always check the stamp on the back of the existing panel before quoting a replacement. Aftermarket panels exist, but we’ve found the tolerances are inconsistent enough that we recommend OEM Belgard panels for mid-run replacements, and we’ll tell you that even when the aftermarket option is cheaper for us to buy, because the callbacks aren’t worth it for anyone.
One other identifying tip: Belgard fences cast a small “B” logo into the back lower corner of most panels. If yours doesn’t have it, you may have a different manufacturer’s system, and we’ll figure that out during the free estimate.
For context, we also stock parts for KraftMaid, Cambria, and Silestone products across our remodeling work, so if this fence project turns into something bigger, we’re already set up for it.
Styles & brands we work with
Signs Your Belgard Fence Installation Is Failing
- Leaning post within a year of install. This is almost always a footing problem. Los Angeles soil varies from sandy loam near the coast to dense clay inland, and a post set in 18 inches of concrete when it needs 30 will start tilting as the ground shifts with the seasons.
- Gate drags or won’t latch. Gates are the first thing to sag on any fence system, and Belgard gates are heavier than wood because they’re precast concrete. The hinge bolts loosen, or the post the gate mounts to shifts slightly, and the latch misses by a quarter inch.
- Panels cracked at the corner. This usually happens during transport or installation, but it can also show up later if a post shifts and transfers pressure to the panel. A hairline crack in a corner will widen over a season of rain and sun.
- White residue blooming on the surface. That’s efflorescence, and it’s normal for concrete products to some degree. But if it’s heavy and won’t brush off, the fence is absorbing too much water, often from a sprinkler head spraying directly on the panel.
- Post cap popped off or missing. These are plastic and they get brittle in Los Angeles sun after a few years. Losing a cap seems cosmetic, but it lets water into the post channel, which accelerates rust on the hardware inside.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Los Angeles, a partial Belgard fence repair (one to three panels plus a post) runs $1,200 to $3,500 installed. A full perimeter re-install or new installation lands between $4,130 and $10,620, depending on linear footage, gate count, and whether we’re removing an old fence first.
Here’s how that breaks down:
- Belgard panel (72″ wide): $280 – $520 per panel depending on height and texture.
- Belgard post and cap: $180 – $310 per post.
- Concrete footing with removal of old post: $120 – $240 per post.
- Gate and hardware: $600 – $1,400 for a complete swing gate assembly.
- Labor and installation: Typically 40 – 50% of the total job.
Every quote includes the written price before we start, the concrete work, leveling, and a full workmanship warranty. Luca Romano has been swinging tools in LA for over two decades, and we don’t change the number at the door. If the fence fails because of something we did wrong, the 365-Day Done Right Promise means we come back and fix it, in writing, no argument.
DIY or Call Us?
If you’re replacing a single panel, you can unbolt it from the posts with a socket set and some patience. The panel is heavy, around 80 to 120 pounds depending on height, so you’ll want a second set of hands and a furniture dolly. That’s a Saturday job for a careful homeowner.
What you shouldn’t DIY is anything involving the post footings. Digging out a failed post, setting a new one to the right depth for LA soil, and getting the alignment right so the panels slide in without binding is the kind of work that looks simple and goes sideways fast. A post set half an inch off plumb becomes a leaning fence in a year. If the post is rusted, cracked, or leaning, call us at (254) 272-5876. We’ll match the panel style, set the post correctly, and warranty the work.
FAQs
With proper installation and concrete footings, a Belgard fence lasts 20 to 30 years in Los Angeles. The weak points are gates and post caps, which typically need replacement every 5 to 10 years due to sun exposure and daily use. Sprinkler overspray is the biggest lifespan killer we see, especially on panels that get hit with mineral-heavy LA water daily.
A hairline crack can sometimes be sealed with a concrete patch product, but for structural cracks at the corners or through the panel face, replacement is the honest fix. Patched panels don’t hold up under fence movement, and you’ll end up replacing it anyway within a season or two. Call (254) 272-5876 and we’ll look at photos before we ever schedule a visit.
A partial repair on a few panels and posts is usually done in one day. A full fence installation takes two to four days depending on the length of the run and how many gates are involved. Demolition of an old fence adds a day, and we handle the debris hauling so you’re not staring at a pile of old concrete.
We keep common Belgard panel sizes, posts, caps, and gate hardware on our trucks, so most repairs don’t require a second trip or a wait for delivery. If you need a specific panel height or texture we don’t have on hand, we order it directly from Belgard’s Southern California distributor and it’s typically in within three to five business days.
If your Belgard fence is leaning, cracked, or the gate won’t close, call (254) 272-5876 for a free estimate. We’ll give you a written price before any work starts, and you’ll know exactly who’s coming and when they’ll arrive. Good work doesn’t need a sales pitch, it just needs to be done right.
Written by Luca Romano, Owner, Sawyer Remodeling at Sawyer Remodeling, serving Los Angeles and nearby areas.
