Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Kitchen Remodeling: The Los Angeles Owner’s Guide
We stock, match, and install Jerith-compatible kitchen remodeling components across Los Angeles, with full kitchen remodels typically running $16,520 – $53,100 depending on cabinet run, countertop footage, and whether we’re pulling permits. If you’re holding a failed Jerith cabinet hinge, a delaminating drawer front, or a drawer slide that’s given up after years of daily use, we can typically source the replacement part and have a technician out within a few days. Most Los Angeles homeowners find out something’s wrong when a cabinet door starts drooping, a drawer binds mid-pull, or a soft-close mechanism stops catching, and by then the underlying hardware has usually been wearing down for months.
We’re an independent Los Angeles remodeling contractor, not a Jerith dealer or factory affiliate. That matters because it means we’re not tied to a single supply line: we do OEM Jerith parts when that’s the right call, and we’ll also tell you when a quality aftermarket equivalent will outlast the original for less money.
Which Jerith Models This Applies To
Jerith’s kitchen cabinetry lines share a lot of DNA under the hood, but there are compatibility gotchas worth knowing before you order anything. The biggest one: Jerith switched hinge bore patterns on several cabinet series in the mid-2010s. Older Jerith lines used a 35mm cup hole with a 9.5mm depth; newer production runs use the same 35mm diameter but a deeper 11mm bore paired with a different mounting plate offset. If you match the hinge by brand name alone, you can end up with a door that won’t sit flush against the face frame, and no amount of adjustment fixes that.
Here’s how we approach it on every Jerith kitchen remodeling job in Los Angeles:
- Check the cabinet box interior. Jerith stamps or labels most boxes on the inside of the sink base or corner cabinet. The label will carry a date code plus a series identifier, and that’s the fastest way to confirm which hinge generation you have.
- Measure the cup bore depth with a digital caliper, not a tape measure. A millimeter of difference changes the hinge entirely.
- Note the drawer slide length and side clearance. Jerith has used both 18-inch and 21-inch side-mount slides across different door styles. Undermount slides on their newer lines need a ½-inch side clearance, and retrofitting an older box to undermount hardware is usually more work than it saves.
- For missing or wrecked doors, we match the door profile, wood species, and finish. Los Angeles kitchens from the 2000s and 2010s are heavy on maple and cherry with a natural or mid-tone stain, and matching aged finishes takes a finish specialist who knows how UV exposure in this climate shifts stain color over time.
OEM versus aftermarket: for hinges and slides, we default to OEM Jerith parts when the series is still in production and the lead time is reasonable. When Jerith has discontinued a line, or when the original part was a known weak point, we step up to commercial-grade aftermarket hardware from Blum or Salice. Those brand names matter because they’re what higher-end cabinetmakers have relied on for years, and they’re the reason we can offer a meaningful warranty on the work.
Styles & brands we work with
Signs Your Jerith Kitchen Remodeling Is Failing
Most Jerith kitchen hardware fails gradually, and Los Angeles homeowners usually notice one of five things first. Each symptom has a specific cause, and knowing the cause tells you whether you’re looking at a simple part swap or something deeper.
- A cabinet door sags or rubs against the frame. The hinge plate has loosened, or the hinge’s internal spring has fatigued. Left alone, the door will start chipping the frame edge, and the hinge cup will wallow out the door bore.
- A drawer opens with a stick or a hard bind. One side of the slide has worn a flat spot on its bearing, or the slide mounting screw pulled loose from the box side. Forcing it just chews up the drawer box further.
- A soft-close door slams instead of catching. The soft-close damper inside the hinge has blown its seal, which happens faster in high-use Los Angeles kitchens where cabinets open and close dozens of times a day.
- A drawer front has separated from the box or wobbles. The connecting screws stripped out, or the glue joint on a mechanical-mount front gave way. This is more common on Jerith’s flat-panel doors where the front is attached with screws through the drawer box wall.
- Finish cracks or dark lines appear around the hinge area. Moisture from a nearby sink, combined with seasonal humidity swings in Los Angeles, has penetrated the door. This is a refinishing job more than a hardware swap, and it’s cheaper to address before the door stock swells permanently.
If you’re seeing one of these, call us at (254) 272-5876. We’ll tell you over the phone whether it sounds like a part we can bring on the first trip or something we need to see in person to match correctly.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Los Angeles homeowners, the cost of Jerith kitchen remodeling work breaks into tiers. A single cabinet hinge replacement with labor typically runs $65 – $140, a full drawer slide swap plus mounting repair runs $95 – $210 per drawer, and refinishing or replacing a matched door runs $180 – $420 per door depending on wood species and finish work needed. Full kitchen remodels on Jerith cabinetry run $16,520 – $53,100, small kitchen remodels $10,620 – $23,600, and cabinet installation alone $4,720 – $15,340.
Every quote from Sawyer Remodeling is a written, line-item price before any work starts. That means the door replacement cost, the hardware cost, the finish-match labor, and any disposal fee are all listed separately, and the number we hand you is the number on the invoice. If a part fails within 365 days, the 365-Day Done Right Promise covers the correction.
DIY or Call Us?
You can safely check a few things yourself: confirm the cabinet label for model info, test which doors and drawers are affected, and take photos of the failing hardware with a coin in the frame for scale. What you don’t want to do is start drilling into cabinet frames, trying to fill a wallowed-out hinge bore, or ordering a “Jerith-compatible” hinge from an online marketplace without confirming the bore depth and plate offset. Cabinet box wood is usually partial-board or plywood, and once you strip a mounting screw or drill an oversized hole, the repair cost goes up because we’re now rebuilding the box, not swapping a part.
If the part is a gas strut, a hinge under spring tension, or anything attached to a heavy door, we recommend letting a trained technician handle it. A 40-pound cabinet door with a failing hinge is a finger pinching hazard, and swapping gas struts on a lift-up door without the right support is how people get hurt. Call (254) 272-5876, tell us what you’re seeing, and we’ll tell you honestly whether it’s a fix you can handle or a job for us.
FAQs
Most Jerith hinges and slides last 15 to 20 years with normal use, but Los Angeles coastal moisture, hard water evaporation near the sink, and heavy daily use can cut that lifespan to 10 to 12 years. Soft-close dampers usually fail first, typically at the 8 to 10 year mark. Call (254) 272-5876 if you’re replacing more than a couple of hinges, because the conversation about a fuller refresh is worth having before you sink money into piecemeal fixes.
A loose hinge plate can often be tightened and re-aligned, and a separated drawer front can sometimes be re-secured if the screw holes are still intact. A blown soft-close damper or a worn slide bearing cannot be repaired practically, and you’ll save money replacing the part rather than patching it. Call (254) 272-5876 for a straight answer on which situation you have.
A single hinge or slide swap takes about 30 to 60 minutes on site, and most part match-and-replace jobs are done in one visit. If we’re replacing multiple doors or refinishing to match, expect 2 to 5 days including finish cure time. Call (254) 272-5876 to schedule, and we’ll give you a written time window before the appointment.
Our Los Angeles technicians carry the most common Jerith hinge plate offsets, 35mm cup hinges, soft-close adapters, and 18-inch and 21-inch side-mount slides. Less common series-specific parts are ordered for same-week arrival. Call (254) 272-5876 with your cabinet label info, and we’ll confirm before the technician rolls out.
If you’re tired of living with a kitchen that fights back every time you open a drawer, call Sawyer Remodeling at (254) 272-5876. We’ll match the right Jerith-compatible part, give you a written price, and get it installed without the runaround. Good work doesn’t need a sales pitch, it just needs to be done right.
Written by Luca Romano, Owner, Sawyer Remodeling at Sawyer Remodeling, serving Los Angeles and nearby areas.
