Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Kitchen Remodeling: The Los Angeles Owner’s Guide
PGT kitchen remodeling in Los Angeles typically runs $16,520 to $53,100, depending on cabinet line, countertop material, and whether walls or plumbing move. We stock PGT-compatible hardware, trim, and replacement components on our trucks, and we install or replace them same-visit in most cases. Most homeowners find us not because the whole kitchen failed, but because one part did: a drawer glide snapped, a hinge stripped out of its plate, a soft-close mechanism stopped catching. The kitchen still works. It just works badly, and that grates on you every single time you reach for a pan.
Which PGT Models This Applies To
PGT has produced several cabinet and hardware lines over the years, and the compatibility gotcha is this: PGT drawer slides and hinge plates changed mounting hole spacing between the early 2000s and the 2010s. A slide from a 2006 model year cabinet will not drop into a 2016 box without a retrofit plate. We measure the hole spread before ordering anything. If you can find the model label inside a drawer or on the hinge cup, that tells us the series. No label? We measure slide length, cabinet depth, and hinge overlay to match the right part.
For most PGT kitchens in Los Angeles, OEM components are the right call for visible hardware like hinges and pulls, because the finish has to match what is already there. Aftermarket equivalents work well for internal parts: drawer slides, corner braces, soft-close dampers, and shelf clips. We carry both. We are an independent service provider, not affiliated with PGT, which means we are free to recommend the part that actually makes sense for your kitchen rather than the one with the right logo on the box.
Styles & brands we work with
Signs Your PGT Kitchen Remodeling Is Failing
- Drawer opens with a thunk or sticks mid-pull. This is usually a worn ball-bearing slide or a bent rail. When one side degrades faster than the other, the drawer racks and the motion gets rough.
- Cabinet door hangs slightly low and won’t close square. The hinge plate has loosened from the cabinet side or the hinge itself has worn at the pivot. Tightening only works until the wood fibers around the screws give out.
- Soft-close mechanism stopped catching. The damper inside the hinge or slide has failed. It is a $15 to $40 part in most cases. Replacing the whole cabinet for that is like replacing a tire for a nail.
- Shelf clips snap or shelves sag under dishes. Original PGT clips are plastic and they embrittle with age, especially in Los Angeles kitchens where dry heat and cooking grease cycle every day. Replacement clips and shelf pins are cheap and we carry them in bulk.
- Corner cabinet hardware binds or the lazy Susan won’t rotate smoothly. The bearing ring or the mounting post has worn. This is more common in older PGT corner units and is a straightforward swap once the cabinet is emptied.
Replacement Cost & What’s Included
For a targeted PGT part replacement – hinges, slides, dampers, shelf hardware – you are typically looking at $236 to $767 installed, including the parts and the labor to remove, fit, and align everything. For a broader refresh where we replace all drawer slides, hinges, and soft-close hardware across a full kitchen while cabinets stay in place, that lands around $2,360 to $7,670. If the cabinet boxes themselves are failing – water damage, delamination, or frames pulling loose – a full kitchen remodel in Los Angeles runs $16,520 to $53,100.
Every quote we write in Los Angeles is a line-item price: parts listed separately, labor listed separately, and the written number is the number you approve before work starts. No change orders because we “found something.” If we open a cabinet and find hidden damage, we stop, show you, and quote the fix before touching it. That is the Relay Standard, and it applies to a $15 shelf clip or a $50,000 remodel the same way.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Most cabinet hardware replacement is safe to attempt if you are patient and have a screwdriver, but here is where DIY goes wrong with PGT specifically: the mounting hole patterns I mentioned. You order a hinge that looks right, install it, and the door sits 1/8 inch proud or the reveal is uneven, and now you have stripped screw holes and frustration. If it is a clip-on shelf pin or a basic pull, go for it. If it is a hinge, a slide, or anything involving alignment, call us. We show up with the right part, the right retrofit plate, and the boring jig if new holes are needed. Call (254) 272-5876 and we will get you sorted.
FAQs
Most PGT hinges and slides last 12 to 18 years under daily use in Los Angeles, but homes near the coast see faster wear from salt air on metal parts, and dry inland heat accelerates plastic clip and damper failure. If your kitchen is 15 years old and the hardware is original, you are in the replacement window.
Slides and soft-close dampers get replaced, not repaired, because the internal bearings and springs are not serviceable. Hinges can sometimes be saved with a retrofit plate if the cabinet-side screw holes are stripped, but a worn pivot means replacement. Call (254) 272-5876 and we will tell you over the phone which category you are in.
A single drawer slide or hinge replacement takes 20 to 45 minutes once we are on site. A full kitchen hardware refresh – all slides, hinges, and soft-close – typically takes half a day to one full day depending on cabinet count. We give you a live arrival time before we head over, so you are not waiting through a four-hour window.
We stock the most common PGT-compatible hinge plates, drawer slides, soft-close dampers, shelf clips, and pulls on our service vehicles in Los Angeles, so most jobs are completed on the first visit. If you have a less common finish or a corner-cabinet bearing ring, we order it and return to install it once it arrives, usually within a few days.
Get Your PGT Kitchen Working Right Again
If a drawer is sticking, a door is sagging, or the soft-close gave up, do not live with it. Call Sawyer Remodeling at (254) 272-5876 for a free estimate. We will match the part to your PGT model, give you a written price before any work starts, and stand behind the install with our 365-Day Done Right Promise. We also carry parts and materials for KraftMaid, Cambria, and Silestone kitchens, so if your remodel touches more than one brand, we can handle it in one trip. Good work doesn’t need a sales pitch – it just needs to be done right.
Written by Luca Romano, Owner, Sawyer Remodeling at Sawyer Remodeling, serving Los Angeles and nearby areas.
